Bar stools are actually the second plan I always built back when I started this unharmed journey a couple years ago. I didn ’ t have much have back then, so it was kinda a trial and error project and took much longer than it actually should have. I didn ’ triiodothyronine cut any corners ( woodworking punnnnnnn
 ) and went with the traditional lean leg. needle to say, there were a set of angles all over the place. It took a while to figure everything out and put it all together, but they turned out decent in the conclusion. Feel release to check that undertaking out over here – DIY Basic Bar Stools .
 ) and went with the traditional lean leg. needle to say, there were a set of angles all over the place. It took a while to figure everything out and put it all together, but they turned out decent in the conclusion. Feel release to check that undertaking out over here – DIY Basic Bar Stools .That first set of stools was supernumerary tall in order to fit the anticipate in our township home. When we moved into our new dwelling, we added a kitchen island with a standard bar acme counter. So it was time for some new ones !
And let me tell ya, this set of barroom stools went much smoother ! All the pieces went in concert like peas and carrots.
Reading: DIY Bar Stools
good a few tips for any first-time stool builders : take your meter, make sure your angles are correct and all boards are the exact same distance, measure 37 times and cut once .
Enjoy the free plans ! I ’ ve written the plans for ONE stool. Adjust as necessity .
This post contains affiliate links. If you make a leverage from one of the links, I may make a little deputation at NO EXTRA COST to you. This helps keep the tutorials and plans free here at Bitterroot DIY. Thank you for your support ! See my full moon disclosure here .
Tools & Supplies
Lumber:
- 2 | 2×2 @ 8′
- 1 | 1×2 @ 8′
- 1 | 2 x 12 @ 15″ (all you need is one 15″ seat)
Cuts:
- 4 | 2×2 @ 28″ with a 5° miter and 5° bevel parallel on both ends (see Step 1 below) – legs
- 2 | 1×2 @ 10.5″ with 5° miter (short side) – bottom rungs
- 2 | 1×2 @ 12″ with 5° miter (short side) – bottom rungs
- 2 | 1×2 @ 7 1/4″ with 5° miter (short side) – top rungs
- 2 | 1×2 @ 9″ with 5° miter (short side) – top rungs
- 1 | 2×12 @ 15″ – seat
Step 1.
To cut the legs, set your attend to a 5° miter joint and 5° bevel. Cut the stock end off the board, slide the circuit board down ( no necessitate to flip it ) and make your future cut at 28″. recur for the next leg .
To keep path of what ’ s what, mark the tallest corner of each leg as you cut. It ’ s a superintendent helpful point I picked up from Ana White the beginning fourth dimension I built stools. The angle is so minor that it ’ mho arduous to keep chase once all the boards are in a pile. Marking them saves a long ton of prison term and headache. The tallest corner is the inside border of the leg .
Step 2.
Align the top 9″ surround sluice with the top of two legs and attach with forest glue and 1 1/4″ pocket hole fuck. Make indisputable the cross off corners of the legs are pointed toward the inside .
Step 3.
Position the 12″ bottom resound according to the diagram below and attach with wood glue and 1 1/4″ pouch hole screws .
recur for the second set of legs .
Step 4.
once you ’ ve finished both sets of legs with top and bottom rungs, join the two sets with the 7 1/4″ top rungs .
Step 5.
Attach the final bottom rungs according to the diagram below with wood glue and 1 1/4″ pocket hole screws .
Step 6.
Fasten the stool legs to the seat from the bottomland side in order to best hide the screw .
There are a total of ways to attach the buttocks. I drilled 2 1/2″ pocket holes into the at heart border of each branch before attaching the rungs and fastened them down with wood glue and 2 1/2″ air pocket hole cheat. You could besides drill straight through the bottom of the peak rungs into the seat ( barely make surely to pre-drill to avoid separate ). You could besides use brackets. Its up to you !
Step 7.
Fill the visible pocket holes, backbone, and polish as desire. I used stainable wood filler in the visible pocket holes and they covered up nicely .
I finished the stools with a new finish from Varathane called “ Weathered Wood Accelerator ” in the brown shade and sealed it with a semi-gloss polycrylic spray .
Let me know if you have any questions and I ’ ll get back to you a soon as possible !
Thanks for stopping by !
For more visualize ideas, you can find me on Pinterest. And to stay up to date with the latest shenanigans, follow me on Instagram.
Don ’ t forget to pin it for late !
 
 
Nhận xét