Instagram Tutorial and Video
I ’ ve set out a bit-by-bit of how I made the chargers below. If you would like to watch a video recording of me painting the charger plate at the assorted steps, check out the highlights on my Instagram account ( linked here ) .
If you prefer the print adaptation, keep on read .
Supplies
I made these plates using acrylic fiber paint that I had in my craft cupboard, but very any acrylic fiber paint would work. The alone thing is that you may want a higher-quality ( i.e., more pigment ) paint to do the basis color. otherwise, it will take quite a few coats.
Painting Your Charger Plate
READ THIS FIRST : Remember that charger plates are the plates that go under your food plate for cosmetic purposes, sort of like a placemat. Because I knew food would never touch these plates, I was not concerned about using acrylic paint to paint them. I would not recommend painting plates that you will be using for food .
Step 1: Paint the charger plate pink
originate by using your pallette knife or paintbrush to mix a grape-size dollop of flannel paint with quarter-pea-size bit of crimson paint to get the tap color. Add more red or white paint a little at a time to get the hope tap color. If you are using a paintbrush to mix the paint, dip your brush in a cup of water to wet it for easier desegregate .
Use a large paintbrush to paint the now-pink paint onto the charger plate. You may need to wet your paintbrush indeed the paint goes on smoothly. The first coat should look like this :
It took me a total of three coats to achieve a solid pink backdrop on the charger plate. Make certain each coat is completely dry before painting the future coat. besides, paint the consecutive coats on LIGHTLY because acrylic paint is water-soluble and you do not want to wash away the undercoats .
Step 2: Paint red spots on top of the now-pink charger plate
This is the easily region. Take a smaller, rounded-tip paintbrush and use it to paint red spots along the outer rim of the charger plate .
You do not want the spots to be undifferentiated ( or flush perfect circles for that matter ). Dab them on. Paint them on. Do whatever works for you to get a good diverseness of spots/splotches. And wear ’ deoxythymidine monophosphate forget to add some fond spots that ( imaginarily ) extend beyond the border .
I painted the outer 1-inch surround of my charger plates because the white dinner plates that I will put on top of the charger are quite large. however, you may need to paint a thick surround depending on the size of your dinner plate .
And in casing you have Valentine ’ s Day on the heed, you could stop here.
Read more: 29 Best Bedroom DIY Ideas and Projects
How cunning is this charger with just the crimson dots ? I may need to do a red kernel adaptation for the kids for Valentine ’ s Day .
Step 3: Paint green spots on top of the red spots
After the red spots dry, use the same brush to paint green spots on top of the red spots .
Use the lapp non-uniform approach–you ’ ll want some green spots to be larger than others. You ’ ll besides want them to be on different sides of the red spots. Some can even be right in the middle .
Step 4: Paint small white spots on top of the green spots
When the park spots dry, use a smaller paintbrush to dab a sting of egg white on top of or to the side of the park spots .
You may need to go spinal column over the ashen when it dries and add a second coat to make it more opaque .
Protecting your painted charger plates
When you finish painting your charger plate, give it a good 24 hours to dry ( although the final layer of white dots should be dry to the touch in less than 20 minutes ). It credibly takes longer than a day for the key to amply harden and dry, but I did an test melt over Thanksgiving, and the charger held up through the meal .
If you love how your chargers turned out and want to keep them ( and store them ) for the long-run, I recommend painting over them with Mod Podge ( Amazon link here ) or a exchangeable sealant to protect the paint. I have not done this tone yet because I want to use the chargers for Christmas and Mod Podge takes 2-3 weeks to cure. I will keep you posted on the results a soon as I do.
Finishing touches
I paired the charger plates with my egg white dishes and these cute red polka-dot napkins from World Market .
then I decorated the center of table with holly branches that I found outdoors along with some votive candles in glasses. The star-like stem is from a dried agapanthus ( those purple, sphere-shaped bunch of flowers that you see in the summer ) .
nowadays to decide what we will be eating for Christmas dinner !
Nhận xét